DynaFlight 97 Flemish Bowstring
When entering the string length needed this will be the actual length of the
string itself "measured off bow" and not the bows length.
Please read below "how to measure string length" before placing a order.
If you have no string then you would put the bows length into the
"additional instruction field" by following these instruction below
"how to measure bow length"
Also note that when ordering a longbow string they come with the
standard smaller loop sizes. So please ask for larger loops if you
have wider longbow limbs.
Order a bowstring with the silencers already installed or un-installed with instructions.
~Flemish Bowstrings are Constructed using B50 or DynaFlight 97~
The original high strength Dyneema (100% SK75); very durable, very low creep.
DynaFLIGHT 97 is much stronger than regular FastFlight and has much lower creep.
For bow's up to 65lbs, very little, if any creep, will be experienced.
The type of bowstring material that you use is entirely up to you. But please make sure
that your bow is designed to take the bow string that you are about to use.
Most older bows with wood or wood/glass limbs are not designed to take the
performance strings such as DynaFlight 97, FastFlight, etc. So if in doubt, stick with B50.
However, if your bow is approved for dynaflight 97, you will find that they not only increase
performance, but also have a longer life span, reduce hand shock and bow vibration,
and offer improved stability and accuracy.
Made from the original polyester material; the ideal product for traditional archers
© Flemishbowstrings 2013
If you have a old string you were shooting with and were happy with the brace height than this would be your best guide:
Take your old string that has been unstrung from the bow for at least 3 hrs. then hammer a small size finish nail into
something sturdy. Now slip one end loop over the nail and take the measurement from this loop end to the other loop end
“tip to tip” while stretching it out "hand tight" just good enough where there is no loose slack in the string.
In most cases a traditional recurve will take a B50 bowstring that is 4" shorter in length measured off the bow than the
AMO "bows length" and a bowstring 3" shorter using DynaFlight97. Longbow strings go 3" shorter than the bows length for
B50 and 2" shorter for DynaFlight97
Example 1: RECURVES
If you have a recurve bow that is 58" in length and wanted a B50 you would want to order a 54" string
If you have a recurve bow that is 58" in length and wanted a DynaFlight97 you would want to order a 55" string
Example 2: LONGBOWS
If you have a longbow that is 58" in length and wanted a B50 you would want to order a 55"string
If you have a longbow that is 58" in length and wanted a DynaFlight97 you would want to order a 56 "string
Very important: If your measuring from a fast flight type of material such as DynaFlight97 and ordering a B50 instead then you
would want to order a B50 approx: 1" shorter than the high performance material because a B50 will stretch and then recover
back approx" 3/4" to 1" while braced depending on your poundage, where a fast flight material such as DynaFlight will stretch
very little if any at all. So in regards if you measured from a B50 and want to change to a DynaFlight string then you would do the
opposite and go with a string 3/4" to 1" longer. If possible please include the bows AMO into the"additional instructions" field.
I do get technical to assure happy and returning customers!
Note that there are times you are in a position to order strictly from the bows AMO if you have no string to measure from.
If this is the case I will follow the standard guidelines above .
If the bow has no markings stating the AMO then please follow below here "how to measure bow length"
How to Choose and Measure Bow String Length:
How To Measure Traditional Bow Length:
If you have no string and there is nothing printed on the bow re: "AMO" or Bow Length then take a tape measure, start at the
nock/string groove of either end "not the bow tips", run tape down the belly (side facing you when you shoot it) of the un-strung
bow following the contours of the bow limbs, do not go into the curves of the handle, go straight across to the opposite nock
groove and read the measure. Enter the length of the bow into the "additional instructions" field if you will be ordering by the
bow length and not the string length and I will make your string by the above standard guidelines.
Beaver Fur Silencers
Halo Center Serving
choose black or tan
All orders are custom made and if there is some defect "very rare"
or wrong length on my part that you original requested I will certainly
replace your order.
Tammy Jo Palmer
500 E Washington St
Weiser, Idaho 83672
Please email me if you have any questions
Shipping and handling anywhere in the US will be a flat $5.95 for any amount ordered.
International orders : Tax and duty fees may be charged by your country when your order arrives.
Those additional charges are your responsibility. Tammy Jo’s Bow Strings ships to most countries.
Minimum shipping and handling charge is $ 23.45
Do to several phone calls a day it would be much easier to
correspond by email where we will be more than happy to
help with any questions or concerns that you may have
during break time.
Please read all the information provided as to help you
choose the correct string
Please allow 2-6 "BUSINESS DAYS" for custom orders
to be completed. They will then be mailed by USPS
Flemishbowstrings, Beaver Fur Silencers, Bowstring Wax
all rights reserved
Pease allow 2 to 6 "BUSINESS DAYS" for custom orders to be completed. They will then be mailed by USPS